Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
What're your beliefs about Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a new one is also a moderately challenging project. If the old tub is readily available, the task can relocate easily; if you have to open a wall surface to get rid of the old bathtub and also position the new bathtub, the task is much harder. In either case, the job is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub as well as set in the brand-new one. Make sure you have actually certified on your own for the job and fit attempting it. Rather than employing a service provider to take control of a halfway-completed job, it is better to consider employing one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This short article will certainly help you mount a new bathtub in your bathroom if you have actually already purchased a new bathtub and do not require to change the arrangement of your previous supply of water pipes.
Your tools as well as product list must make up the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be fairly troublesome as a result of the restricted gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Before going on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washers are in location in between the tap as well as the sink. Protect the tap in place with the producer supplied backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Utilizing the two wooden boards under its feet, put the bath tub in the needed placement. The wood boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to make sure that the tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bath tub until the level reads degree.
To install taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Turn on the water system and also examine all joints and new pipework for leaks and also tighten them if essential. Load the bath tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait till the tub has actually been used at the very least once as this will certainly resolve it into its last position.
Preparing for the Setup
To start with, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to pass through the wall between the bath and also the tiling, bring about complications with dampness as well as feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes as well as cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water before securing, to permit the activity experienced when the tub is in use. The sealant can split relatively early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily available on the market. It is suggested to fit the floor tiles utilizing waterproof or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on Tools You Need to Install a New Bathtub ? Try leaving a remark directly below. We will be glad to see your responses about this blog. We are looking forward that you come back again in the near future. Are you aware of another person who is curious about How to Install a Bathtub Yourself? Please feel free to promote it. Thanks for your time. Don't forget to check our site back soon.
Request Estimate Report this page